Summit BIM70 User Manual

Automatic Ice Maker User's Manual Be sure unit is standing upright 24 hours prior to plug-in. Model: BIM70

9 • To ensure proper ventilation for your ice maker, the front of the unit must be completely unobstructed. Allow at least 101 mm (4”) clearance at

10 Electrical Shock Hazard Plug into a grounded 3-prong outlet. Never remove the grounding prong from the plug. Never use an adapter. Ne

11 Leveling the Ice Maker It is important for the ice maker to be leveled in order to work properly. It can be raised or lowered by rotating the

12Nut of water draining hole Connecting the water line: 1. Turn off main water supply. Turn on nearest faucet long enough to clear the line of wate

13of the ice storage bin. 3. All horizontal runs of drain lines must have a fall of ¼” per foot. An air gap will likely be required between the ic

14Final Check List before Operation 1. Have all packing materials and tape been removed from the interior and exterior of the ice maker? 2. Did you

15 Operating Method 1. Switch on the Power switch on the right side panel. The light will be on. The ice maker will start working automatically a

16Harvest: During the harvest cycle the compressor is still operating, but the water pump has stopped. Two other components have been energized: the

17 ● Water running from the water sump to the evaporator plate may make a splashing sound. ● Water running from the evaporator to the water sump m

18 CLEANING AND MAINTENANCE If the ice maker is left unused for a long time, before the next use it must

Table of Contents Page ICE MAKER SAFETY ... 2 IMPORT

19The door and cabinet may be cleaned with a mild detergent and warm water solution such as 1 oz of dishwashing liquid mixed with 2 gallons of warm w

20 Interior Cleaning The ice storage bin should be sanitized occasionally. Clean the bin before the ice maker is used for the first time and reused

21 2. Take out the row of flake covers by snapping one end up and pulling forward. 3. Remove the slideway from the water sump.

22water. Rinse thoroughly with clear water. 7. Reassemble the sprinkler arm, slideway and row of flake covers. 8. Perform steps 1, 3, 6, 7 and 8

23 5. Allow 30 minutes for proper cleaning. After cleaning, shut off the power switch, and unscrew the nut of the water-draining hole on the rear o

24 Control Box (behind front cover) Descriptions of LEDs and buttons: 1. Red LED: Ice Full indicator light. When t

255. Mode button: Mainly for service. When this button is pressed, unit can change from Ice Making mode to Ice Harvest mode, or from Ice Harvest m

26 MAJOR FUNCTIONS 1. Completely automatic operating procedure. 2. When the ice storage bin is full of ice cubes, the machine stops working auto

27 TROUBLESHOOTING Before Calling for Service If the unit appears to be malfunctioning, read through the Operation section of this manual first.

28 LIMITED WARRANTY

2 ICE MAKER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and o

29 PARTS AND LABOR WARRANTY INFORMATION SUMMIT appliances are manufactured to provide outstanding value, and your satisfaction is our goal on every

30 NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE: There are no other warranties, expressed, implied or statutory, ex

31 Tested and certified to NSF standard 12 by NSF International Probado y certificado por NSF International de acuerdo con la norma NS

3 IMPORTANT SAFEGUARDS Before the ice maker is used, it must be properly positioned and installed as described in this manual, so read the manual

4  The ice maker should not be located next to ovens, grills or other sources of high heat.  The ice maker must be installed with all electrical

5power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

6 INTRODUCTION This SUMMIT Ice Maker finds wide application in households, bars, restaurants, hotels, supermarkets, etc. This unit produces cry

7 COMPONENT LOCATIONS Door Ice cube full sensor Front cover Ventilation louvers Leveling caster Control box (behind front

8 ICE MAKER INSTALLATION Unpacking Excessive Weight Hazard Use two or more people to move and install ice maker. Failure to do so can result